Product and Retail Links
SPLITBOARD AND EXTRA FAT CRAMPONS
Retail Outlets:
Mammoth Gear
Mammoth Lakes, CA
The Fifth Season
Mount Shasta, CA
ROAM
Nelson, BC
Alpenglow Sports
Tahoe City, CA
The Backcountry
Truckee, CA
Neptune Mountaineering
Boulder, CO
Warning:
Ski mountaineering is an exceptionally hazardous activity which often results in severe injuries and death. Any person purchasing, or using our equipment, assumes the responsibility for seeking proper training in its use. They also assume all risk for injury, or damage, sustained while using any of our equipment. Our equipment is not to be used for any other purpose other than which it is intended. Failure to follow these warnings increase the risk of injury or death. B & D Precision is not, and shall not, be liable for direct, indirect, incidental, or other types of damages arising out of, or resulting from, the use of our products.
Always test your gear before heading to the backcountry!
Dynafit Custom Accessories
Radical Heel Lift Extensions "Nubbins" Are in Stock,
Toe Shims to Decrease Ramp
B & D Ski Gear makes several custom components for Dynafit bindings including top plates, shims, volcanoes, and Nubbins.
See Below for Details
Custom Dynafit Products
Dynafit Speed Plates
Fits on the TLT and Comfort binding to reduce weight for those looking to save every gram. The stock TLT plates with post weigh 80 gms.
Weigh 20 grams per set
Only available in red.
Speed Plates $21.95
Pricing
Top Plates
Engraving at additional cost.
Heel Risers
Shims
Toe Shims $32.95
Comfort Extensions $10.00
Screws $0.40 each
Light Lateral Release Springs $21.95
Click Here to Order
Shims or Springs
Contact us for additional sizes or custom orders.
Light Lateral Release
Springs for Dynafit
We stock light lateral release springs for Dynafit bindings that allow the DIN to be reduced to approximately "3". While not endorsed by Dynafit they may improve the possibility of release for individuals under 100 lbs. Note that the heel post rotates with very little pressure and these springs must be tested with great attention to detail.
We do not guarantee the safety or function of these springs.
We do allow you to return these if you are not satisfied.
Comfort Top Plate
Weigh 42 grams per set.
Available in black and red.
Note riser cones/volcanoes must be purchased separately.
Black on a Goode
Comfort plate on classic binding.
Comfort Plates $24.95
B & D cones can be added so you can have a comfort style cone on a TLT speed binding or Race T1 bindings (my favorite).
Nubbins for Radicals
Many people noticed that the Radical heel lifters are not as tall as the Comforts. Our Nubbins, or heel lift extenders, raise the Radical heel riser to the level of the Comfort/Vertical cones. The Nubbin attaches to the heel riser with a set screw.
17gms (0.6 Oz) per set w/screws
Nubbins $26.95Dynafit may refuse to warranty heel units if they feel Nubbins contributed to the heel unit's failure.
Comfort Style Heel Riser Cones/Volcanoes
Ask and ye shall receive. People have been searching for a viable replacement for the weak Dynafit heel risers for years. After debating the pros and cons we decided to produce a stronger, and lighter heel riser. Our cones are available in a variety of sizes.
The short cones are 1/4" shorter than the stock cones.
Weighs 19gms (0.7 Oz)
The standard cones are the same size as the stock cones.
Weighs 26gms (0.9 Oz)
The tall cones are 1/4" taller than the stock cones.
Weighs 33gms (1.2 Oz)
Cones are only sold in pairs.
Our cones are at least 50% stronger than stock Dynafit cones. They will mount onto stock comfort top plates and our custom top plates. They come with screws for mounting.
Disclaimer:
These cones are not a replacement for good technique. Most cones are probably broken due to bad technique, not weakness of the cones. We will not accept any responsibility for damage to your heel unit while using any of our products.
Toe shims for Dynafit bindings that raise your toe height by 1/4". The main use for the toe shim is to reduce the amount of ramp in your binding. While these shims were made with the Radicals in mind, they will work with most Dynafit bindings.
The shims are made out of the same type of plastic as our cones. They are machined out on the bottom to make them as light as possible.
We also offer extensions for our toe shims to support the plastic tab present in comfort style toe pieces. Due to variances in boot sole length we do not offer a wedge to support the plastic strip connecting the toe and heel units in the Verticals.
Shims Weigh 70gms (2.5 Oz)
Extensions Weigh 62gms (2.2 Oz)
These shims do not come with screws.
We sell 19mm long screws for use with Dynafit Radical Speed and Race versions at $0.40 per screw.
We sell 28mm long screws for use with Dynafit Radical FT, and Comfort/Vertical bindings at $0.40 per screw.